CAMheads CNC Router Forum By: CAMaster CNC

Go Back   CAMheads CNC Router Forum By: CAMaster CNC > Search Forums

Showing results 1 to 25 of 258
Search took 0.01 seconds.
Search: Posts Made By: Logan Y
Forum: General Discussion Yesterday, 10:29 AM
Replies: 5
Views: 186
Posted By Logan Y
I actually have a branding iron for my company...

I actually have a branding iron for my company logo and I thought about that. The issues is this logo needs to be 5"x5" and that'll run $400 just for the new head. It is the cheapest option but it...
Forum: The Water Cooler Yesterday, 10:24 AM
Replies: 2
Views: 97
Posted By Logan Y
Someone will be along with specifics but there...

Someone will be along with specifics but there are multiple options on relocating the controls.

I picked the easiest option which was to remove the buttons from the side of the box and run wire to...
Forum: General Discussion 04-20-2021, 06:47 PM
Replies: 5
Views: 186
Posted By Logan Y
The project I have for it is logo burning. I...

The project I have for it is logo burning. I don't really plan on ever cutting anything with it. I know you supposedly can but at 7W I believe your ipm would have to be pretty slow.
Forum: General Discussion 04-20-2021, 11:46 AM
Replies: 5
Views: 186
Posted By Logan Y
WinCNC upgrade worth it

I'm in the process of adding on the jtech laser to my machine. I have a charity job coming up that I need it for and adding that makes the most sense for me versus buying a separate machine. I can't...
Forum: Stinger I (Table Top) 04-18-2021, 05:01 PM
Replies: 6
Views: 178
Posted By Logan Y
Agree with the above. It sounds like the collet...

Agree with the above. It sounds like the collet may not be seated all the way in the nut. Make sure to insert the collet into the nut before putting the nut on the tool cone. The collet should snap...
Forum: General Discussion 04-14-2021, 05:49 PM
Replies: 1
Views: 106
Posted By Logan Y
Yes. With your machine you can take a full depth...

Yes. With your machine you can take a full depth path of that material at a decent clip (500+ ipm).
Forum: Cobra CNC Routers 04-14-2021, 02:45 PM
Replies: 14
Views: 396
Posted By Logan Y
I turn my air off between uses and my spindle...

I turn my air off between uses and my spindle doesn't drop. Granted I have a smaller spindle than some of you but the weight is still relatively significant. I always park my machine before I turn it...
Forum: The Water Cooler 04-09-2021, 08:34 AM
Replies: 5
Views: 287
Posted By Logan Y
Technically the machines are made for nonferrous...

Technically the machines are made for nonferrous cutting snd drilling so drilling steel would be iffy. I know they have a modified Cobra at the factory they do it with but it's not your run of the...
Forum: The Water Cooler 04-08-2021, 08:02 PM
Replies: 12
Views: 320
Posted By Logan Y
And if you go to an RV park all of these rules go...

And if you go to an RV park all of these rules go out the window. Almost every person you'll meet at an RV park carries a variety of dogbones that allow them step down to lower rated circuits. The...
Forum: The Water Cooler 04-08-2021, 06:54 PM
Replies: 12
Views: 320
Posted By Logan Y
I should have been more clear. What you are...

I should have been more clear. What you are saying is both correct and incorrect. It isn't good practice to do either option in most circumstances. It is also good to remember that you shouldn't ever...
Forum: Stinger III 04-08-2021, 05:15 PM
Replies: 5
Views: 245
Posted By Logan Y
That is measuring the tool you are using. The...

That is measuring the tool you are using. The machine needs to know how long the tool is so it knows where it is in space below the spindle.

Have you done your orientation training with CAMaster...
Forum: Panther Series 04-08-2021, 05:13 PM
Replies: 13
Views: 414
Posted By Logan Y
It would likely need to be a tracked bobcat for...

It would likely need to be a tracked bobcat for it to work since those are typically larger and have a lifting capacity to match. The wheeled versions are usually in the 2-3k lbs range lifting wise....
Forum: The Water Cooler 04-08-2021, 05:06 PM
Replies: 12
Views: 320
Posted By Logan Y
You can use a 50 amp receptacle on a 30 amp...

You can use a 50 amp receptacle on a 30 amp circuit depending on the wiring configuration but you should never use a 30 amp receptacle on a 50 amp circuit. The receptacle won't handle the load and...
Forum: Panther Series 04-08-2021, 08:17 AM
Replies: 13
Views: 414
Posted By Logan Y
I have the Titan pallet fork extensions. ...

I have the Titan pallet fork extensions.

Double check your neighbors lift capacity and ensure there's an appropriate amount of counterbalance. To have a FEL tractor rated for that much weight it...
Forum: Panther Series 04-07-2021, 10:24 PM
Replies: 13
Views: 414
Posted By Logan Y
Also consider telehandlers/skytracks with forks....

Also consider telehandlers/skytracks with forks. You can get the fork extensions for cheap on Amazon or rent them a lot of places. I used a tracked skid steer with forks and Amazon extensions to...
Forum: New Forum Members 04-06-2021, 08:13 AM
Replies: 2
Views: 307
Posted By Logan Y
Use either the CAMaster Single Tool post...

Use either the CAMaster Single Tool post processor or the Tool Change one depending in if you have FTC or not.
Forum: The Water Cooler 04-01-2021, 03:01 PM
Replies: 3
Views: 271
Posted By Logan Y
Depending on the size of the cuts you are making...

Depending on the size of the cuts you are making a larger diameter compression bit would probably be your best choice. I know a lot of guys are fond of the 3/8" compression bits. It gives you enough...
Forum: New Forum Members 03-31-2021, 12:01 PM
Replies: 19
Views: 995
Posted By Logan Y
If you were closer I'd give you my old harbor...

If you were closer I'd give you my old harbor freight dust collector that I upgraded with a Wynn filter. I used it in my detached garage shop at the house before I moved 90% of my dust producing...
Forum: materials and bits, collets, etc. 03-29-2021, 04:06 PM
Replies: 6
Views: 309
Posted By Logan Y
https://www.usroutertools.com/Long-Bits-For-Wood-s...

https://www.usroutertools.com/Long-Bits-For-Wood-s/365.htm
Forum: General Discussion 03-28-2021, 08:14 PM
Replies: 2
Views: 161
Posted By Logan Y
The post processor won't change from a single...

The post processor won't change from a single sided to double sided project. You will have separate tool paths obviously for each side. I like to save those as different files so I don't accidently...
Forum: New Forum Members 03-24-2021, 07:57 AM
Replies: 6
Views: 292
Posted By Logan Y
I'm 2.5-3 hours south of you. I'm no expert by...

I'm 2.5-3 hours south of you. I'm no expert by any means but if you want to come see my machine and what it's capable of just send me a private message.
Forum: Elite Series 03-20-2021, 11:06 AM
Replies: 7
Views: 317
Posted By Logan Y
Is the spindle cone clean of debris? It sounds...

Is the spindle cone clean of debris? It sounds like it started with the clamp sticking. You shouldn't ever have to pull to remove the tool. The weight of the tool should be enough to drop thr tool...
Forum: New owner Setup issues 03-15-2021, 08:01 PM
Replies: 15
Views: 247
Posted By Logan Y
It's really dependent on the size of the "smaller...

It's really dependent on the size of the "smaller board" and the size of the zone you have one. The smallest board I feel comfortable holding is a 12" round bread board I make. I cut it on one of my...
Forum: FAQ Frequently Asked Questions 03-14-2021, 08:43 PM
Replies: 4
Views: 291
Posted By Logan Y
Try clearing your cache. It sounds like it isn't...

Try clearing your cache. It sounds like it isn't loading a full view of the page for some reason.
Forum: General Discussion 03-14-2021, 08:02 PM
Replies: 2
Views: 168
Posted By Logan Y
The only real change is setting separate tool...

The only real change is setting separate tool numbers for each tool you will use in Aspire. Also use the Tool Change Inch Post Processor and make sure all of your toolpaths are output to one file.
...
Showing results 1 to 25 of 258

 
Forum Jump

All times are GMT -4. The time now is 06:41 AM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2021, Jelsoft Enterprises Ltd.